A8522KLPTR-T

• Product Introduction

The A8522 is a programmable multi-output LED driver for LCD backlighting. The driver integrates a current-type boost regulator with a built-in power switch and eight current absorbers. The ICs operate from 4.5 to 36 volts and can withstand load dumps of up to 40 volts that occur in automotive systems.

An optimized control loop will eliminate night flash in monitor backlighting applications.

The I2C interface allows users to set the LED current individually, up to 60 mA per LED channel. Adjacent channels can be combined to drive higher current LED strings. The PWM dimming duty cycle can also be controlled individually for each LED channel. This flexibility makes the A8522 a single solution for various LED applications. and report the fault status via dual communication.

The PWM dimming duty cycle can also be controlled individually for each LED channel. This flexibility makes the A8522 a single solution for a variety of LED applications, i.e., in some cases, replacing two or more LED driver ICs with a single device.

The A8522 detects and prevents various fault conditions and reports fault status via dual communication. It features output short-circuit and over-voltage protection, open-circuit or short-circuit secondary tube protection, open-circuit or short-circuit LED pin protection, short-circuit boost switch or inductor protection, and IC over-temperature protection. Dual cycle-by-cycle current limiting prevents switching overcurrent on the built-in switch. If required, the IC can drive an external PFET that acts as an input disconnect switch, which is triggered by an integrated current sensor.

Apply:

Car:

• 资讯娱乐
• 群集
• 车辆中控面板照明
• 抬头显示器 (HUD)
• 白天行驶灯 (DRL)
• • AEC Q100 标准认证
  • 宽输入电压范围为 4.5 至 36 V
  • 可承受低至 3.9 伏（V_IN 下降）的怠速停止和高达 40  伏的甩负荷
  • 整合带 DMOS 开关的升压稳压器，过压保护高达 39 V
  • 8 个完全整合的 LED 电流吸收器，每通道的电流可单独编程达 60 mA
  • I²C™ 接口，用于编程 LED 电流、PWM 调光和每通道的各个保护阈值
  • 使用单个 IC 驱动多个负荷
  • 宽广的 PWM 调光范围（在 100 Hz 时高达 10,000:1），可为每个通道单独编程
  • 广泛的诊断和故障报告
  • 在较高温度时发出热警告和使 LED 电流降额
  • 针对所有通道的缓冲 PWM 调光控制，以促进局部调光应用
  • 多相 PWM 调光：参差调谐的 LED 电流，以降低闪光和输入纹波电流
  • 同步升压开关频率：400 kHz 至 2.3 MHz ，允许低于或高于 AM 段工作
  • 可编程频率抖动以降低 EMI
  • 典型 LED 电流准确率为 0.7%，LED 至 LED 匹配准确率为 0.8%。
  • 保护功能
    • 开路/短路 LED 引脚检测
    • 可编程 LED 串短路检测
    • 开路/短路外部组件（包括升压电感、肖特基二极管、FSET 电阻器等）
    • 预防输出至 GND 短路的输入过流保护
    • 逐周期开关电流限制
    • 过温、输出过压和欠压保护